T-HOBBY Velox Victory V3008 Cinematic Fpv Drone Motor

Ultimate Flight Performance V3008 Motors

Optimised for 7-8’models to provide long-lasting flight time.

Excellent Stability

Optimised design to reduce vibration and enhance vehicle stability.

High-quality and Superb Craftsmanship

The stability and durability of the motor is guaranteed, providing total safety during flight.

Safe & Worry-Free Flight

Rigorously tested motors to ensure safety and reliability during every flight.

Specifications

Size

Package Included

Data Test

Buyer’s Guide: T-HOBBY Velox Victory V3008 Motor 

When engineering a 7-inch to 8.5-inch long-range mountain cruiser, a high-speed cinematic follow rig, or a lightweight Cinelifter, finding the sweet spot between low cruise amperage and high-throttle authority is critical. The T-HOBBY Velox Victory V3008 Cinematic FPV Drone Motor ($1155\text{KV} / 1350\text{KV} / 1500\text{KV}$) utilizes a wide 30mm stator diameter paired with an 8mm stator height and high-grade curved magnets, producing broad magnetic leverage to control 7"–8.5" props smoothly without the excessive mass or amp consumption of heavy 31-series stators.

Pilot Flight Impressions

"Upgrading from standard 2806.5 and 2808 stators to the Velox Victory V3008 on an 8-inch mountain cruiser completely changed how the quad handles strong crosswinds and low-speed tracking lines. The wider 30mm stator creates exceptional low-end magnetic grip—holding a flat cinematic line at 55 km/h with an action camera feels locked-in and takes significantly less throttle micro-management. When punching over ridgelines or braking out of steep alpine dives, the motor grabs clean air instantly with zero prop-wash shudder or squishy throttle hesitation. Even after pushing continuous 15-minute cruise sessions on a 6S Li-Ion pack, the bell housings land only moderately warm thanks to the open-spoke cooling architecture, and the 4mm internal shaft holds up to rough field touchdowns without bending or throwing bell balance."

Recommended Ecosystem & Hardware Pairings

● Flight Controller & ESC Stack: 55A–65A 4-in-1 ESC Stack with STM32F722 MCU (e.g., Flywoo GOKU F722 Pro V2 55A Stack, T-HOBBY Velox F7 SE / V50A SE Stack).

● Propellers: 7-inch to 8.5-inch Cinematic and Long-Range Propellers (e.g., HQProp DP 7x4x3, Gemfan 7040 / 7535, HQ 8x4x3, MEPS 8045).

● Batteries:

        ● Long-Range Cruise: 6S 4000mAh–8000mAh 21700 Li-Ion Packs (e.g., GEPRC Storm 6S2P 8000mAh, iFlight Fullsend 6S 4000mAh).

        ● Cinematic High-Burst: 6S 1750mAh–2200mAh 150C LiPo Packs (e.g., Boslipo P7 1750mAh 150C 6S).

● Frames: 7-inch to 8.5-inch Long-Range Deadcat or Cinematic Frames (e.g., iFlight Chimera7, GEPRC Crocodile7, Mark4 7"–8").

● FPV & Navigation: DJI O3 Air Unit, Walksnail Avatar HD Pro, high-power analog VTX, and independent GPS rescue modules.

T-HOBBY Velox Victory V3008 vs. T-HOBBY V3115

Selection Summary

● Choose the T-HOBBY Velox Victory V3008 if: You are building a 7-inch to 8.5-inch long-range mountain exploration quad or high-speed cinematic follow rig carrying an action camera (GoPro Hero 11/12/13 or DJI O3). At ~70g per corner, it delivers wide-stator torque and wind resistance while saving ~175g over heavy 3115 stators to preserve precious Li-ion battery endurance.

● Choose the T-HOBBY V3115 Smooth if: You are building an 8-inch to 11-inch Cinelifter or an X8 heavy-payload platform carrying full-size cinema packages (like a RED Komodo, BMPCC 6K, or Sony FX3). Its tall 15mm stator and high-voltage capability deliver the raw lifting authority and thermal headroom needed to swing large 9"–11" carbon props without motor saturation.

Recommended Parts

● T-HOBBY C80A-4IN1-8S 80A ESC Dual MOSFET for FPV Drone

● T-HOBBY Velox F7 SE Flight Controller - 30.5x30.5 F7 FC for FPV Drones

● MEPS 8045 FPV Propeller for 8 inch FPV Drone

Recommendations