NeuBETAFPV F4 2-3S 20A AIO FC BETAFPV V1 Integrierter HD VTX für Whoop Drohnen

F4 2-3S 20A AIO FC V1 is specifically designed for HD VTX, utilizing 2-3S batteries for enhancing the flight experience. It features a dual BEC solution that delivers stable power outputs of 9V@2A for DJI O3 and 5V@3A for external devices. With a 20A ESC, it enables agile flight and increases dynamic. And connector for DJI O3 HD VTX and USB port for easy installation and maintenance. Ideal for HD VTX whoop enthusiasts, offering a heightened level of professionalism and convenience with this FC option.

Specification

• Weight: 5.58g (without motor connectors and power cable),5.92g (with motor connectors)
  

• Mounting Hole Size: 26mm x 26mm

• CPU*: STM32F405RGT6 (168MHz)

• Six-Axis: ICM42688P (SPI connection)

• RX: Serial ELRS 2.4G Receiver

• RX firmware version: BETAFPV AIO 2400 RX ELRS V3.3.0

• Antenna: Enameled wire

• Blackbox Memory: 16MB

• Sensor: Barometer (BMP280/DSP310),  Voltage & Current

• 5V BEC*: 5V 3A@8V supply

• 9V BEC*: 9V 2A@8V supply
  

• USB Port: SH1.0 4-Pin

• Built-in ESC with 20A continuous and peak 25A current

• ESC input voltage: 2-3S

• FC firmfware version: Betaflight_4.4.1_BETAFPVF405

• ESC firmware: C_X_70_48_V0.19.2.hex for BB51 Bluejay hardware

• Signal support: D-shot300, D-shot600

Note: If you use the F4 2-3S 20A AIO FC V1, the serial port of the SBUS receiver is UART5 while F4 1S 12A AIO Brushless FC V3 is UART6.

F4 2-3S 20A AIO FC V1 also has extended the USB port to the end for easier parameter adjustment and wiring. And a new DJI O3 6-pin PMU has been added for convenient installation and maintenance.

Power cutoff: Removing the chip bead disconnects the power supply, and to reuse the onboard ELRS receiver, soldering the solder pads together restores power.

UART3 release: Removing two resistors on the solder pads releases UART3. The left side is TX3, and the right side is RX3. To reconnect, solder the solder pads together when reusing the onboard ELRS receiver.

Voltage Switch: The HD VTX connector defaults to 9V. The chip bead is soldered between the 9V pad and the middle pad. To use WalkSnail Avatar HD mini 1s and Lite, please ensure the power supply voltage is 5V. Remove the chip bead first from the 9V pad and solder it between the middle pad and the 5V pad. Alternatively, you can use solder instead the chip bead to switch between the 5V and 9V pads.

Motor choice: Avoid selecting motors with excessively high KV ratings, as motors above 20,000KV are prone to burn.

ESC Firmware

With BB51 ESC solution, F4 2-3S 20A AIO FC V1 is based on BLHeliSuite16714903 with Bluejay ESC firmware, it supports bidirectional D-shot and RPM filtering in Betaflight, offers 24KHz, 48KHz, and 96KHz fixed PWM frequency for options, and custom start-up melodies. F4 2-3S 20A AIO FC V1 default factory setting is 48KHz and it doesn’t recommend upgrading the 96KHz, or it might cause an error in the motor idle setting, not spinning when disarmed.

DO NOT flash the firmware with a shorter interval, otherwise, there will be a certain chance of stalling and burning the flight controller.

Serial ELRS 2.4G RX

Serial ELRS 2.4G RX uses the Crossfire serial protocol (CRSF protocol) to communicate between the receiver and the flight controller board. So the Serial ELRS 2.4G RX is available to support upgrading to ELRS V3 with no need to flash Betaflight flight controller firmware. 

• Enter binding status by power on/off three times.

• Plugin and unplug the flight controller three times;

• Make sure the RX LED is doing a quick double blink, which indicates the receiver is in bind mode;

• Make sure the RF TX module or radio transmitter enters binding status, which sends out a binding pulse;

• If the receiver has a solid light, it's bound.

The Serial ELRS 2.4G RX can be updated via Wi-Fi or Betaflight serial passthrough. Here is the way to update the Serial ELRS 2.4G RX firmware through passthrough.

• Plug in your FC to your computer, but do NOT connect to betaflight configurator.

• Choose target "BETAFPV 2.4GHz AIO RX". 

• Flash using the BetaflightPassthrough option in ExpressLRS Configurator.

Connecting External Devices

Please note that the board reserves two serial ports and a standard SBUS port, which is available for the external CRSF protocol receiver or GPS module, and SBUS protocol receiver. You can refer to the below picture.

Package

• 1 * F4 2-3S 20A AIO FC V1

• 4 * M2*10 Machine Screw 

• 4 * M2*10 Nylon Screw 

• 4 * M2 Nuts 

• 4 * Shock Absorbing Ball 

• 4 * JST1.25mm Angle Socket 

• 4 * JST1.25mm Straight Socket 

• 1 * SH1.0 4Pin Adapter Cable

• 1 * Type-C to SH1.0 Adapter 

• 1 * XT30 Power Cord

• 1 * Filter Capacitor 

• 1 * 30mm Double-head VTX connector wire 

• 1 * 60mm Single-head VTX connector wire